Crucial SSD not working, possible controller error

MrSheep

New Member
Credits
15
Hi everyone.

I'm trying to get an old SSD to be detected by my Fedora Linux installation. It is a Crucial M4 128GB sata drive which is producing a lot of errors and I fear it might be dead or dying.

I currently get these messages when I connect it.
Code:
[Mar 8 16:18] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[  +0.040266] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20200925/psargs-330)
[  +0.000005] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20200925/psparse-529)
[  +0.000113] ata6.00: failed to enable AA (error_mask=0x1)
[  +0.000010] ata6.00: ATA-9: M4-CT128M4SSD2, 070H, max UDMA/100
[  +0.000000] ata6.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 32)
[  +0.000327] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20200925/psargs-330)
[  +0.000003] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20200925/psparse-529)
[  +0.000072] ata6.00: failed to enable AA (error_mask=0x1)
[  +0.000002] ata6.00: configured for UDMA/100 (device error ignored)
[  +0.001139] scsi 5:0:0:0: Direct-Access     ATA      M4-CT128M4SSD2   070H PQ: 0 ANSI: 5
[  +0.000151] sd 5:0:0:0: [sdf] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[  +0.000005] sd 5:0:0:0: [sdf] Write Protect is off
[  +0.000001] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[  +0.000002] sd 5:0:0:0: Attached scsi generic sg5 type 0
[  +0.000004] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  +0.025093] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6
[  +0.000002] ata6.00: irq_stat 0x40000001
[  +0.000001] ata6.00: failed command: READ FPDMA QUEUED
[  +0.000003] ata6.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq dma 4096 in
                       res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x403 (HSM violation) <F>                                                                                                                              
[  +0.000002] ata6: hard resetting link
[  +0.309516] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[  +0.000366] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20200925/psargs-330)
[  +0.000006] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20200925/psparse-529)
[  +0.000058] ata6.00: failed to enable AA (error_mask=0x1)
[  +0.000342] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.SPT5._GTF.DSSP], AE_NOT_FOUND (20200925/psargs-330)
[  +0.000003] ACPI Error: Aborting method \_SB.PCI0.SAT0.SPT5._GTF due to previous error (AE_NOT_FOUND) (20200925/psparse-529)
[  +0.000069] ata6.00: failed to enable AA (error_mask=0x1)
[  +0.000002] ata6.00: configured for UDMA/100 (device error ignored)
[  +0.001063] ata6: EH complete
[ +30.478567] ata6.00: NCQ disabled due to excessive errors
[  +0.000008] ata6.00: exception Emask 0x0 SAct 0x800 SErr 0x0 action 0x6 frozen
[  +0.000006] ata6.00: failed command: READ FPDMA QUEUED
[  +0.000010] ata6.00: cmd 60/08:58:00:00:00/00:00:00:00:00/40 tag 11 ncq dma 4096 in
                       res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)                                                                                                                                                    
[  +0.000003] ata6.00: status: { DRDY }
[  +0.000006] ata6: hard resetting link
[  +5.354988] ata6: link is slow to respond, please be patient (ready=0)
[  +4.679996] ata6: COMRESET failed (errno=-16)
[  +0.000003] ata6: hard resetting link
[  +5.352052] ata6: link is slow to respond, please be patient (ready=0)
[  +4.680024] ata6: COMRESET failed (errno=-16)
[  +0.000008] ata6: hard resetting link
[  +5.353014] ata6: link is slow to respond, please be patient (ready=0)
[Mar 8 16:19] ata6: COMRESET failed (errno=-16)
[  +0.000004] ata6: limiting SATA link speed to 3.0 Gbps
[  +0.000001] ata6: hard resetting link
[  +5.043063] ata6: COMRESET failed (errno=-16)
[  +0.000009] ata6: reset failed, giving up
[  +0.000004] ata6.00: disabled
[  +0.000022] ata6: EH complete
[  +0.000042] sd 5:0:0:0: [sdf] tag#15 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=90s
[  +0.000007] sd 5:0:0:0: [sdf] tag#15 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000006] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000006] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000123] sd 5:0:0:0: [sdf] tag#1 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000008] sd 5:0:0:0: [sdf] tag#1 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000005] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000005] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000039] sd 5:0:0:0: [sdf] tag#2 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000004] sd 5:0:0:0: [sdf] tag#2 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000004] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000003] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000024] ldm_validate_partition_table(): Disk read failed.
[  +0.000012] sd 5:0:0:0: [sdf] tag#3 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#3 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000003] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000001] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000015] sd 5:0:0:0: [sdf] tag#4 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#4 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000002] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000001] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000015] sd 5:0:0:0: [sdf] tag#5 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#5 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000002] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000001] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000015] sd 5:0:0:0: [sdf] tag#6 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#6 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000002] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000001] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000005] Dev sdf: unable to read RDB block 0
[  +0.000012] sd 5:0:0:0: [sdf] tag#7 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#7 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000002] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000002] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000014] sd 5:0:0:0: [sdf] tag#8 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#8 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  +0.000002] blk_update_request: I/O error, dev sdf, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[  +0.000001] Buffer I/O error on dev sdf, logical block 0, async page read
[  +0.000005]  sdf: unable to read partition table
[  +0.000379] sd 5:0:0:0: [sdf] Read Capacity(16) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  +0.000001] sd 5:0:0:0: [sdf] Sense not available.
[  +0.000011] sd 5:0:0:0: [sdf] Read Capacity(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  +0.000001] sd 5:0:0:0: [sdf] Sense not available.
[  +0.000013] sd 5:0:0:0: [sdf] 0 512-byte logical blocks: (0 B/0 B)
[  +0.000009] sd 5:0:0:0: [sdf] Write Protect is on
[  +0.000001] sd 5:0:0:0: [sdf] Mode Sense: 1c 1e 1f cc
[  +0.000019] sd 5:0:0:0: [sdf] Attached SCSI disk
[  +0.000072] sd 5:0:0:0: [sdf] Read Capacity(16) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  +0.000002] sd 5:0:0:0: [sdf] Sense not available.
[  +0.000018] sd 5:0:0:0: [sdf] Read Capacity(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  +0.000001] sd 5:0:0:0: [sdf] Sense not available.
[Mar 8 16:22] sd 5:0:0:0: [sdf] tag#17 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK cmd_age=0s
[  +0.000002] sd 5:0:0:0: [sdf] tag#17 CDB: ATA command pass through(16) 85 06 2c 00 00 00 00 00 00 00 00 00 00 00 e5 00

Could somebody please interpret what this means as I don't really understand it other than it being error messages. My initial interpretation would be that this is a sata controller error on my drive.
I know for certain that my motherboard and cable are all working fine, since other drives connected to the same port aredetected properly

Thank You
 


Lord Boltar

Active Member
Credits
2,427
Since a majority of it is ACPI related I would say it is a bios bug is there an update for the bios?

Try booting with the "acpi=off" kernel parameter This will disable ACPI support. If the error is the same with ACPI enabled and disabled, this may not be an ACPI issue.
 

f33dm3bits

Gold Member
Gold Supporter
Credits
14,461
In my experience i/o errors are often a sign of a failing disk or shortly to fail, but I don't if that is the same for ssd's although I would expect that any type of storage device to be able to get i/o errors.
 
$100 Digital Ocean Credit
Get a free VM to test out Linux!

Staff online

Members online


Latest posts

Top